Subpackages callable global parameters

For any defined object (that has its own tag) after finishing the analysis, user can call the parameters that that are evaluated. Each object has global parameters and also its internal defined parameters. In this part global parameters of each object that users can call and check the resulted values are described.

Note

The called parameters return the results of the current analyzed scenario or current loaded scenario. So, if user get the following parameters after MultiParallel analysis command, it just returns the last scenario result. So, if user wants to get all scenario results the following ways are applicable:

• Use UniAnalyze analysis in a loop and call the desired parameters after the analysis command. (Not Suggested)

• Use Objs_recorder_loader commands and load the ObjsRecorder file and load it into the memory and then using load1ScenarioOfBank(ScenarioTag) loop on all ScenarioTags and call the desired parameter/s.

Hazard

Parameter	Description
SampledMagnitude	Obvious.

Example:

In the following example the Earthquake has defined with tag 1 and its SampledMagnitude has been called.

Python Code

opr.Hazard.ObjManager.TagObjDict[1].SampledMagnitude

DateAndTime

Parameter	Description
Day_Night_Ratio	Defined by user.
SampledisDay	A boolean that shows the result of sampling. True shows it is day.

Example:

In the following example the Datetime has defined with tag 1 and its SampledisDay has been called:

Python Code

opr.DateAndTime.ObjManager.TagObjDict[1].SampledisDay

WindData

Parameter	Description
WindClass	Class of sampled wind
WindDirection	Direction of sampled wind.
WindSpeed	Speed of sampled wind.
AlphaCOEF	Alpha coefficient of sampled wind.
isCalmn	The calm condition of sampled wind. True shows the calm condition.

Example:

In the following example the WindData has defined with tag 1 and its Wind speed has been called:

Python Code

opr.WindData.ObjManager.TagObjDict[1].WindSpeed

Sites

Nothing special to call.

Substance

Nothing special to call.

Fragilities

Nothing special to call.

Connectors

Nothing special to call.

Safety

Nothing special to call.

OutFlowModel

Note

This class can not be called directly and it should be called from the object(like plant unit) that it was assigned to. Look at the following example.

Parameter	Description
t_release	Returns list of the release time.
MassLiquidReleaseRate	Returns list of Liquid release rate at each t_release.
dMassLiquid_release	Returns list of released mass of the liquid at each t_release.
TotalMassLiquid_Release	Returns list of total released mass at each t_release.
MassGasReleaseRate	Returns list of Gas mass release rate at each t_release.
dMassGas_release	Returns list of released mass of the gas at each t_release.
TotalMassGas_Release	Returns list of total released mass of gas at each t_release.

Example:

To get list of total gas released of the PlantUnit with tag 1 :

Python Code

opr.PlantUnits.ObjManager.TagObjDict[1].OutFlowModelObject.TotalMassGas_Release

DispersionSpreadModels

Note

This class can not be called directly and it should be called from the object(like plant unit) that it was assigned to. Look at the following example.

Parameter	Description
t_disp	Returns list of the Dispersion time.
LiquidRadious	Returns list of the liquid radius at each t_disp.
LiquidCenter	Returns list of the liquid center at each t_disp.
LiquidThickness	Returns list of the liquid thickness at each t_disp.
t_dispLiquidVaporization	Returns list of the liquid vaporization time.
LiquidVaporizationMassRate	Returns list of the vaporization mass rate at each t_dispLiquidVaporization.
LiquidVaporizationMass	Returns list of the total vaporized mass at each t_dispLiquidVaporization.
GasExplosiveMass	Returns list of the total explosive mass at each t_dispLiquidVaporization.
GasExplosiveCenterX	Returns list of the explosive mass x center at each t_dispLiquidVaporization.
GasExplosiveCenterY	Returns list of the explosive mass y center at each t_dispLiquidVaporization.
GasExplosiveCenterZ	Returns list of the explosive mass z center at each.

Example:

To get list of total mass of vaporized gas of the PlantUnit with tag 1 :

Python Code

opr.PlantUnits.ObjManager.TagObjDict[1].DispersionSpreadModelObject.GasExplosiveMass

PhysicalEffect

Note

This class can not be called directly and it should be called from the object(like plant unit) that it was assigned to. Look at the following example.

Parameter	Description
Thermal_Radiation_at_Point(x,y,z)	Returns thermal radiation and entered point.
RadiationBoundary(Radiation,Height,PointNumber)	Returns Boundary points with equal radiation value equal to entered Radiation and entered height.
OverPressure_at_Point(x,y,z)	Returns over pressure value at entered point.
OverPressureBoundary(OverPressure, Height, PointNumber)	Returns Boundary points with equal Over pressure value equal to entered Radiation and entered height.

Example:

To get Thermal radiation value of a fired PlantUnit with tag 1 at point with coordinate (5,8,2):

Python Code

opr.PlantUnits.ObjManager.Objlst[1].PhysicalEffectObject.Thermal_Radiation_at_Point(5,8,2)

PlantUnits

Parameter	Description
DamageSource	Returns damage source name.
DamageSourceTag	Returns damage source tag.
DamageSourceDose	Returns damage source dose.
DamageSourceType	Returns damage source type.
DamageFragilityTag	Returns Fragility/Probit tag that cause damage.
DamageLevel	Returns damage level.
OutFlowModelTag	Returns Outflow model tag.
OutFlowModelname	Returns Outflow model name.
OutFlowModelObject	Returns Outflow model object.
DispersionSpreadModelTag	Returns Dispersion model tag.
DispersionSpreadModelname	Returns Dispersion model name.
DispersionSpreadModelObject	Returns Dispersion model Object.
PhysicalEffectModelTag	Returns Physical effect model tag.
PhysicalEffectModelname	Returns Physical effect model name.
PhysicalEffectObject	Returns Physical effect model object.

Example:

To get Damage Source of a damaged PlantUnit with tag 1:

Python Code

opr.PlantUnits.ObjManager.Objlst[1].DamageSource

NodesGroup

Parameter	Description
isDamagedList	Returns list of damage condition of each node
DamageSource	Returns list of damage source name of each node
DamageSourceTag	Returns list of damage source tag of each node
DamageSourceDose	Returns list of damage source dose of each node
DamageSourceType	Returns list of damage source type of each node
Radiation_Intensity	Returns list of Radiation dose of each node
OverPressure_Intensity	Returns list of OverPressure dose of each node
Toxic_Intensity	Returns list of Toxic dose of each material of each node
Radiation_Probit	Returns list of probit value corresponding to the Radiation value at each node [Probit(Radiation)]
OverPressure_Probit	Returns list of probit value corresponding to the OverPressure value at each node [Probit(OverPressure)]

Example:

To get list of Damage Source of all nodes that defined with NodesGroup tag 1 :

Python Code

opr.NodesGroup.ObjManager.Objlst[1].DamageSource